Wika IPT-11 Bedienungsanleitung

Operating InstructionsExternal indicating and adjustment unitDocument ID:31550

4 Mounting4.1 General instructionsThe external indicating and adjustment unit functions in any installationposition. The housing can be rotated by 330

62mm (2 7/16")12mm(15/32")7mm (9/32")85mm (3 11/32")Fig. 4: External indication and adjustment unit for wall mounting. Bottom view

132Fig. 6: External indicating and adjustment unit for pipe mounting1 4 screws M5 x 122 Measuring instrument holder3 Tube12 External indicating and ad

5 Connecting to power supply5.1 Preparing the connectionAlways keep in mind the following safety instructions:l Connect only in the complete absence o

5.2 Connection procedureProceed as follows:1 Unscrew the housing cover2 If an indicating and adjustment module is installed, remove it byturning it sl

12 Screw the housing cover onThe electrical connection is finished.5.3 Wiring planDisplayI2C5 6 7 8123Fig. 8: Electronics and connection compartment1 S

Display5 6 7 84 1 2Fig. 9: Wiring plan external indicating and adjustment unit for 4 … 20 mA/HARTsensors1 To the sensor2 Grounding on both ends with n

Display5 6 7 841Fig. 10: Wiring plan external indicating and adjustment unit for PA/FF sensors1 To the sensorConnection via confectioned cable with 5-

6 Set up with the indicating and adjustmentmodule6.1 Short descriptionThe indicating and adjustment module is used for measured valuedisplay, adjustme

Fig. 11: Insert indicating and adjustment moduleNote:If you intend to retrofit the instrument with an indicating and adjustmentmodule for continuous me

Contents1 About this document1.1 Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41.2 Target group . . . . . . . . . . . .

6.3 Adjustment system1.1231Fig. 12: Indicating and adjustment elements1 LC display2 Indication of the menu item number3 Adjustment keysl [OK] key:- Mo

6.4 Setup stepsSetup and adjustment of the respective sensor is carried out accordingto the operating instructions manual of the respective sensor.Ext

7 Maintenance and fault rectification7.1 MaintenanceIf the instrument is used properly, no special maintenance is requiredin normal operation.7.2 Instr

8 Dismounting8.1 Dismounting stepsWarning:Before dismounting, be aware of dangerous process conditions suchas e.g. pressure in the vessel, high temper

9 Supplement9.1 Technical dataGeneral data316L corresponds to 1.4404 or 1.4435, 316Ti corresponds to 1.4571Materials- Housing plastic PBT, Alu die-cas

Electrical protective measuresProtection rating- Housing plastic IP 66/IP 67- Housing Aluminium, stainless steel IP 66/IP 68 (0.2 bar)Overvoltage cate

9.2 DimensionsHousingM20x1,5M20x1,5/½ NPT23~ 69 mm(2 23/32")ø 77 mm(3 1/32")112 mm (4 13/32")M20x1,5/½ NPT1~ 69 mm(2 23/32")ø 77 m

External indicating and adjustment unit 279 Supplement31550-EN-100726

WIKA Alexander Wiegand SE & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyPhone +49 9372 132295Fax +49 9372 132706e-mail: support-tron

Supplementary documentationInformation:Supplementary documents appropriate to the ordered version comewith the delivery. You can find them listed in ch

1 About this document1.1 FunctionThis operating instructions manual provides all the information youneed for mounting, connection and setup as well as

2 For your safety2.1 Authorised personnelAll operations described in this operating instructions manual must becarried out only by trained specialist

2.5 Safety label on the instrumentThe safety approval markings and safety tips on the device must beobserved.2.6 CE conformityThis device fulfills the

3 Product description3.1 StructureThe scope of delivery encompasses:l External indicating and adjustment unitl Cable entry M20x1 for the sensorl Docum

3.2 Principle of operationThe external indicating and adjustment module is used for remotemeasured value indication and parameter adjustment for IPT-1

3.4 Packaging, transport and storageYour instrument was protected by packaging during transport. Itscapacity to handle normal loads during transport i